File pnp4nagios-init of Package pnp4nagios

#! /bin/sh
# Copyright (c) 2007 SuSE Linux AG Nuernberg, Germany.
#
# Author: Lars Vogdt 
#
# /etc/init.d/npcd
#
#   and symbolic its link
#
# /usr/sbin/rcnpcd
#
# System startup script for ncpd
#
### BEGIN INIT INFO
# Provides:       npcd
# Required-Start: $local_fs $remote_fs monitoring_daemon
# Required-Stop:  $local_fs $remote_fs monitoring_daemon
# Should-Start:   httpd2
# Should-Stop:    $null
# Default-Start:  3 5
# Default-Stop:   0 1 2 6
# Short-Description: Nagios-Perfdata-C-Daemon 
# Description:    Starts and stops the Nagios-Perfdata-C-Daemon
#   to provide an asynchronous mode to handle performance data 
#   with nagios.
### END INIT INFO

. /etc/rc.status

NPCD_BIN=/usr/bin/npcd
NPCD_CFG=/etc/pnp4nagios/npcd.cfg
PID=/var/run/npcd.pid

# Check for missing binaries (stale symlinks should not happen)
# Note: Special treatment of stop for LSB conformance
test -x $NPCD_BIN || { echo "$NPCD_BIN not installed";
    if [ "$1" = "stop" ]; then exit 0;
    else exit 3; fi; }

# Check for existence of needed config file and read it
test -r $NPCD_CFG || { echo "$NPCD_CFG not existing";
    if [ "$1" = "stop" ]; then exit 0;
    else exit 3; fi; }

# Reset status of this service
rc_reset

case "$1" in
    start)
        echo -n "Starting npcd "
        startproc -p $PID $NPCD_BIN -d -f $NPCD_CFG
        rc_status -v
    ;;
    stop)
        echo -n "Shutting down npcd " 
        killproc -TERM $NPCD_BIN
		for i in 1 2 3 4 5 6 7 8 9 10 ; do
			if $0 status > /dev/null; then
				echo -n '.'
				killproc -TERM $NPCD_BIN
				sleep 1
			else
				break
			fi
		done
        rc_status -v
    ;;
    try-restart|condrestart)
        ## Do a restart only if the service was active before.
        ## Note: try-restart is now part of LSB (as of 1.9).
        ## RH has a similar command named condrestart.
        if test "$1" = "condrestart"; then
            echo "${attn} Use try-restart ${done}(LSB)${attn} rather than condrestart ${warn}(RH)${norm}"
        fi
        $0 status
        if test $? = 0; then
            $0 restart
        else
            rc_reset    # Not running is not a failure.
        fi
        # Remember status and be quiet
        rc_status
    ;;
    restart)
        $0 stop
        $0 start
        rc_status
    ;;
    force-reload)
        $0 reload
        rc_status
    ;;
    reload)
        echo -n "Reload service npcd "
        killproc -HUP $NPCD_BIN
        touch $PID
        rc_status -v
    ;;
    status)
        echo -n "Checking for service npcd "
        checkproc $NPCD_BIN
        rc_status -v
    ;;
    probe)
        test $NPCD_CFG -nt $PID && echo reload
    ;;
	*)
        echo "Usage: $0 {start|stop|status|try-restart|restart|force-reload|reload|probe}"
		exit 1
    ;;
esac
rc_exit