File dhcpd.conf of Package dhcp.19307
# /etc/dhcpd.conf
#
# Sample configuration file for ISC dhcpd
#
# *** PLEASE CONFIGURE IT FIRST ***
#
# Don't forget to set the DHCPD_INTERFACE in the
# /etc/sysconfig/dhcpd file.
#
# option definitions common to all supported networks...
#option domain-name "example.org";
#option domain-name-servers ns1.example.org, ns2.example.org;
#default-lease-time 600;
#max-lease-time 7200;
# if you do not use dynamical DNS updates:
#
# if you want to use dynamical DNS updates, you should first read
# read /usr/share/doc/packages/dhcp-server/DDNS-howto.txt
#
#ddns-updates off;
# Use this to enble / disable dynamic dns updates globally.
#ddns-update-style none;
# If this DHCP server is the official DHCP server for the local
# network, the authoritative directive should be uncommented.
#authoritative;
# Use this to send dhcp log messages to a different log file (you also
# have to hack syslog.conf to complete the redirection).
#log-facility local7;
#
# Define RFC 3442 classless static route option (121);
# the following _example_ routes:
# 192.168.2.254/32 via 0.0.0.0 (device route)
# 192.168.2.253/32 via 192.168.1.2 (255.255.255.255)
# 192.2.0.128/25 via 192.168.1.2 (255.255.255.128)
# 192.168.2.0/24 via 192.168.1.2 (255.255.255.0)
# 172.16.0.0/12 via 192.168.1.2 (255.240.0.0)
# 10.0.0.0/8 via 192.168.1.2 (255.0.0.0)
# default via 192.168.1.1
# have to be written as:
# option rfc3442-classless-static-routes
# 32, 192, 168, 2, 254, 0, 0, 0, 0,
# 32, 192, 168, 2, 253, 192, 168, 1, 2,
# 25, 192, 2, 0, 128, 192, 168, 1, 2,
# 24, 192, 168, 3, 192, 168, 1, 2,
# 12, 172, 16, 192, 168, 1, 2,
# 8, 10, 192, 168, 1, 2,
# 0, 192, 168, 1, 1;
#
# Note: you have to specify the default gateway here
# as well, because when classless routes are in use,
# the 'routers' option is ignored by the dhcp client.
#
#option rfc3442-classless-static-routes code 121 = array of unsigned integer 8;
#
# Define RFC 4833 timezone options:
#
#option rfc4833-tz-posix-string code 100 = string;
#option rfc4833-tz-name code 101 = string;
#
# Use example:
# option rfc4833-tz-posix-string "EST5EDT4,M3.2.0/02:00,M11.1.0/02:00";
# option rfc4833-tz-name "Europe/Zurich";
# No service will be given on this subnet, but declaring it helps the
# DHCP server to understand the network topology.
#subnet 10.152.187.0 netmask 255.255.255.0 {
#}
# This is a very basic subnet declaration.
#subnet 10.254.239.0 netmask 255.255.255.224 {
# range 10.254.239.10 10.254.239.20;
# option routers rtr-239-0-1.example.org, rtr-239-0-2.example.org;
#}
# This declaration allows BOOTP clients to get dynamic addresses,
# which we don't really recommend.
#subnet 10.254.239.32 netmask 255.255.255.224 {
# range dynamic-bootp 10.254.239.40 10.254.239.60;
# option broadcast-address 10.254.239.31;
# option routers rtr-239-32-1.example.org;
#}
# A slightly different configuration for an internal subnet.
#subnet 10.5.5.0 netmask 255.255.255.224 {
# range 10.5.5.26 10.5.5.30;
# option domain-name-servers ns1.internal.example.org;
# option domain-name "internal.example.org";
# option routers 10.5.5.1;
# option broadcast-address 10.5.5.31;
# default-lease-time 600;
# max-lease-time 7200;
#}
# Hosts which require special configuration options can be listed in
# host statements. If no address is specified, the address will be
# allocated dynamically (if possible), but the host-specific information
# will still come from the host declaration.
#host passacaglia {
# hardware ethernet 0:0:c0:5d:bd:95;
# filename "vmunix.passacaglia";
# server-name "toccata.fugue.com";
#}
# Fixed IP addresses can also be specified for hosts. These addresses
# should not also be listed as being available for dynamic assignment.
# Hosts for which fixed IP addresses have been specified can boot using
# BOOTP or DHCP. Hosts for which no fixed address is specified can only
# be booted with DHCP, unless there is an address range on the subnet
# to which a BOOTP client is connected which has the dynamic-bootp flag
# set.
#host fantasia {
# hardware ethernet 08:00:07:26:c0:a5;
# fixed-address fantasia.fugue.com;
#}
# You can declare a class of clients and then do address allocation
# based on that. The example below shows a case where all clients
# in a certain class get addresses on the 10.17.224/24 subnet, and all
# other clients get addresses on the 10.0.29/24 subnet.
#class "foo" {
# match if substring (option vendor-class-identifier, 0, 4) = "SUNW";
#}
#
#shared-network 224-29 {
# subnet 10.17.224.0 netmask 255.255.255.0 {
# option routers rtr-224.example.org;
# }
# subnet 10.0.29.0 netmask 255.255.255.0 {
# option routers rtr-29.example.org;
# }
# pool {
# allow members of "foo";
# range 10.17.224.10 10.17.224.250;
# }
# pool {
# deny members of "foo";
# range 10.0.29.10 10.0.29.230;
# }
#}