File 0029-Use-upstream-bcm2835.dtsi-to-fix-rp.patch of Package u-boot
From 198d5a9b14f81d70d8599a06a570420971b23344 Mon Sep 17 00:00:00 2001
From: Fabian Vogt <fvogt@suse.com>
Date: Tue, 13 Sep 2016 11:04:31 +0200
Subject: [PATCH] Use upstream bcm2835.dtsi to fix rpi1 build
---
arch/arm/dts/bcm2835.dtsi | 208 +++-------------------------------------------
1 file changed, 10 insertions(+), 198 deletions(-)
diff --git a/arch/arm/dts/bcm2835.dtsi b/arch/arm/dts/bcm2835.dtsi
index 8fc2eb2..a78759e 100644
--- a/arch/arm/dts/bcm2835.dtsi
+++ b/arch/arm/dts/bcm2835.dtsi
@@ -1,213 +1,25 @@
-#include <dt-bindings/pinctrl/bcm2835.h>
-#include <dt-bindings/clock/bcm2835.h>
-#include "skeleton.dtsi"
+#include "bcm283x.dtsi"
/ {
compatible = "brcm,bcm2835";
- model = "BCM2835";
- interrupt-parent = <&intc>;
- chosen {
- bootargs = "earlyprintk console=ttyAMA0";
+ cpus {
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ cpu@0 {
+ device_type = "cpu";
+ compatible = "arm,arm1176jzf-s";
+ reg = <0x0>;
+ };
};
soc {
- compatible = "simple-bus";
- #address-cells = <1>;
- #size-cells = <1>;
ranges = <0x7e000000 0x20000000 0x02000000>;
dma-ranges = <0x40000000 0x00000000 0x20000000>;
- timer@7e003000 {
- compatible = "brcm,bcm2835-system-timer";
- reg = <0x7e003000 0x1000>;
- interrupts = <1 0>, <1 1>, <1 2>, <1 3>;
- /* This could be a reference to BCM2835_CLOCK_TIMER,
- * but we don't have the driver using the common clock
- * support yet.
- */
- clock-frequency = <1000000>;
- };
-
- dma: dma@7e007000 {
- compatible = "brcm,bcm2835-dma";
- reg = <0x7e007000 0xf00>;
- interrupts = <1 16>,
- <1 17>,
- <1 18>,
- <1 19>,
- <1 20>,
- <1 21>,
- <1 22>,
- <1 23>,
- <1 24>,
- <1 25>,
- <1 26>,
- <1 27>,
- <1 28>;
-
- #dma-cells = <1>;
- brcm,dma-channel-mask = <0x7f35>;
- };
-
- intc: interrupt-controller@7e00b200 {
- compatible = "brcm,bcm2835-armctrl-ic";
- reg = <0x7e00b200 0x200>;
- interrupt-controller;
- #interrupt-cells = <2>;
- };
-
- watchdog@7e100000 {
- compatible = "brcm,bcm2835-pm-wdt";
- reg = <0x7e100000 0x28>;
- };
-
- clocks: cprman@7e101000 {
- compatible = "brcm,bcm2835-cprman";
- #clock-cells = <1>;
- reg = <0x7e101000 0x2000>;
-
- /* CPRMAN derives everything from the platform's
- * oscillator.
- */
- clocks = <&clk_osc>;
- };
-
- rng@7e104000 {
- compatible = "brcm,bcm2835-rng";
- reg = <0x7e104000 0x10>;
- };
-
- mailbox: mailbox@7e00b800 {
- compatible = "brcm,bcm2835-mbox";
- reg = <0x7e00b880 0x40>;
- interrupts = <0 1>;
- #mbox-cells = <0>;
- };
-
- gpio: gpio@7e200000 {
- compatible = "brcm,bcm2835-gpio";
- reg = <0x7e200000 0xb4>;
- /*
- * The GPIO IP block is designed for 3 banks of GPIOs.
- * Each bank has a GPIO interrupt for itself.
- * There is an overall "any bank" interrupt.
- * In order, these are GIC interrupts 17, 18, 19, 20.
- * Since the BCM2835 only has 2 banks, the 2nd bank
- * interrupt output appears to be mirrored onto the
- * 3rd bank's interrupt signal.
- * So, a bank0 interrupt shows up on 17, 20, and
- * a bank1 interrupt shows up on 18, 19, 20!
- */
- interrupts = <2 17>, <2 18>, <2 19>, <2 20>;
-
- gpio-controller;
- #gpio-cells = <2>;
-
- interrupt-controller;
- #interrupt-cells = <2>;
- };
-
- uart0: uart@7e201000 {
- compatible = "brcm,bcm2835-pl011", "arm,pl011", "arm,primecell";
- reg = <0x7e201000 0x1000>;
- interrupts = <2 25>;
- clocks = <&clocks BCM2835_CLOCK_UART>,
- <&clocks BCM2835_CLOCK_VPU>;
- clock-names = "uartclk", "apb_pclk";
- arm,primecell-periphid = <0x00241011>;
- };
-
- i2s: i2s@7e203000 {
- compatible = "brcm,bcm2835-i2s";
- reg = <0x7e203000 0x20>,
- <0x7e101098 0x02>;
-
- dmas = <&dma 2>,
- <&dma 3>;
- dma-names = "tx", "rx";
- status = "disabled";
- };
-
- spi: spi@7e204000 {
- compatible = "brcm,bcm2835-spi";
- reg = <0x7e204000 0x1000>;
- interrupts = <2 22>;
- clocks = <&clocks BCM2835_CLOCK_VPU>;
- #address-cells = <1>;
- #size-cells = <0>;
- status = "disabled";
- };
-
- i2c0: i2c@7e205000 {
- compatible = "brcm,bcm2835-i2c";
- reg = <0x7e205000 0x1000>;
- interrupts = <2 21>;
- clocks = <&clocks BCM2835_CLOCK_VPU>;
- #address-cells = <1>;
- #size-cells = <0>;
- status = "disabled";
- };
-
- sdhci: sdhci@7e300000 {
- compatible = "brcm,bcm2835-sdhci";
- reg = <0x7e300000 0x100>;
- interrupts = <2 30>;
- clocks = <&clock_mmc>;
- status = "disabled";
- };
-
- i2c1: i2c@7e804000 {
- compatible = "brcm,bcm2835-i2c";
- reg = <0x7e804000 0x1000>;
- interrupts = <2 21>;
- clocks = <&clocks BCM2835_CLOCK_VPU>;
- #address-cells = <1>;
- #size-cells = <0>;
- status = "disabled";
- };
-
- i2c2: i2c@7e805000 {
- compatible = "brcm,bcm2835-i2c";
- reg = <0x7e805000 0x1000>;
- interrupts = <2 21>;
- clocks = <&clocks BCM2835_CLOCK_VPU>;
- #address-cells = <1>;
- #size-cells = <0>;
- status = "disabled";
- };
-
- usb@7e980000 {
- compatible = "brcm,bcm2835-usb";
- reg = <0x7e980000 0x10000>;
- interrupts = <1 9>;
- };
-
arm-pmu {
compatible = "arm,arm1176-pmu";
};
};
-
- clocks {
- compatible = "simple-bus";
- #address-cells = <1>;
- #size-cells = <0>;
-
- /* The oscillator is the root of the clock tree. */
- clk_osc: clock@3 {
- compatible = "fixed-clock";
- reg = <3>;
- #clock-cells = <0>;
- clock-output-names = "osc";
- clock-frequency = <19200000>;
- };
-
- clk_mmc: clock@1 {
- compatible = "fixed-clock";
- reg = <0x1>;
- #clock-cells = <0x0>;
- clock-output-names = "mmc";
- clock-frequency = <250000000>;
- };
- };
};
