File sec.rc of Package sec

#!/bin/sh
#
# /etc/init.d/sec
#   and its symbolic link
# /(usr/)sbin/rcsec
#
# LSB compatible service control script; see http://www.linuxbase.org/spec/
# 
### BEGIN INIT INFO
# Provides:          sec
# Required-Start:    $syslog $remote_fs
# Should-Start: $time ypbind smtp
# Required-Stop:     $syslog $remote_fs
# Should-Stop: $time ypbind smtp
# Default-Start:     3 5
# Default-Stop:      0 1 2 6
# Short-Description: sec is an simple event correlator
# Description:       sec is an simple event correlator
### END INIT INFO

SEC_BIN=/usr/bin/sec.pl
test -x $SEC_BIN || { echo "$SEC_BIN not installed"; 
	if [ "$1" = "stop" ]; then exit 0;
	else exit 5; fi; }

# Check for existence of needed config file and read it
SEC_CONFIG=/etc/sysconfig/sec
test -r $SEC_CONFIG || { echo "$SEC_CONFIG not existing";
	if [ "$1" = "stop" ]; then exit 0;
	else exit 6; fi; }

# Read config	
. $SEC_CONFIG

. /etc/rc.status

# Reset status of this service
rc_reset

case "$1" in
    start)
	echo -n "Starting simple event correlator (sec)"
	## Start daemon with startproc(8). If this fails
	## the return value is set appropriately by startproc.
	/sbin/startproc $SEC_BIN $SEC_OPTS

	# Remember status and be verbose
	rc_status -v
	;;
    stop)
	echo -n "Shutting down simple event correlator (sec)"
	## Stop daemon with killproc(8) and if this fails
	## killproc sets the return value according to LSB.

	/sbin/killproc -TERM $SEC_BIN

	# Remember status and be verbose
	rc_status -v
	;;
    try-restart|condrestart)
	## Do a restart only if the service was active before.
	## Note: try-restart is now part of LSB (as of 1.9).
	## RH has a similar command named condrestart.
	if test "$1" = "condrestart"; then
		echo "${attn} Use try-restart ${done}(LSB)${attn} rather than condrestart ${warn}(RH)${norm}"
	fi
	$0 status
	if test $? = 0; then
		$0 restart
	else
		rc_reset	# Not running is not a failure.
	fi
	# Remember status and be quiet
	rc_status
	;;
    restart)
	## Stop the service and regardless of whether it was
	## running or not, start it again.
	$0 stop
	$0 start

	# Remember status and be quiet
	rc_status
	;;
    force-reload)
	## Signal the daemon to reload its config. Most daemons
	## do this on signal 1 (SIGHUP).
	## If it does not support it, restart the service if it
	## is running.

	echo -n "Reload service simple event correlator (sec)"
	## if it supports it:
	/sbin/killproc -HUP $SEC_BIN
	#touch /var/run/jftpgw.pid
	rc_status -v

	## Otherwise:
	#$0 try-restart
	#rc_status
	;;
    reload)
	## Like force-reload, but if daemon does not support
	## signaling, do nothing (!)

	# If it supports signaling:
	echo -n "Reload service simple event correlator (sec)"
	/sbin/killproc -HUP $SEC_BIN
	#touch /var/run/jftpgw.pid
	rc_status -v
	
	## Otherwise if it does not support reload:
	#rc_failed 3
	#rc_status -v
	;;
    status)
	echo -n "Checking for service simple event correlator (sec)"
	## Check status with checkproc(8), if process is running
	## checkproc will return with exit status 0.

	# Return value is slightly different for the status command:
	# 0 - service up and running
	# 1 - service dead, but /var/run/  pid  file exists
	# 2 - service dead, but /var/lock/ lock file exists
	# 3 - service not running (unused)
	# 4 - service status unknown :-(
	# 5--199 reserved (5--99 LSB, 100--149 distro, 150--199 appl.)
	
	# NOTE: checkproc returns LSB compliant status values.
	/sbin/checkproc $SEC_BIN
	# NOTE: rc_status knows that we called this init script with
	# "status" option and adapts its messages accordingly.
	rc_status -v
	;;
    *)
	echo "Usage: $0 {start|stop|status|try-restart|restart|force-reload|reload}"
	exit 1
	;;
esac
rc_exit