openSUSE Build Service

Overview Repositories Revisions Requests Users Attributes Meta

File x10.conf of Package heyu

# Example Heyu configuration file.  Copy this to file 'x10config' in
# directory $HOME/.heyu/ and modify as required. This example uses
# features which are new to heyu version 2
# and which will not be recognized by heyu version 1.xx.

# Note: This example file describes only a few of the most commom
# configuration directives.  For the complete list see man page
# x10config(5).

# Anything on a line between a '#' character and the end of the line is
# treated as a comment and ignored by Heyu, as are blank lines.
# The various configuration directives in this file can be in any order
# except that ALIAS directives must appear before any other directive
# which references the alias label in place of a housecode|unit address.
# See 'man x10config' for additional information and directives.

# Serial port to which the CM11a is connected. Default is /dev/ttyS0.

TTY	/dev/ttyS0

# If you have an X10 compatible RF receiver connected to a second
# and model of receiver.  Supported receivers are W800RF32, MR26A,
# and RFXCOM.  There are no defaults.

# Base housecode.  The default is A.

# HOUSECODE	  A                # A B C D E F G H I J K L M N O P

# Aliases:
# Format:  ALIAS  Label  Housecode|Unitcode_string  [Module_Type]
#
# The label is limited to 32 characters in length and is case-sensitive,
# e.g., Front_Porch and front_porch are treated as different labels.
# Each alias may reference a single unitcode or a multiple unitcode
# string (no embedded blanks), but is limited to one housecode.
#
# The optional Module_Type is the general type or specific model number
# of a module currently supported by Heyu. (Knowing the characteristics
# of a module allows Heyu to track changes in its On/Off/Dim state
# as X10 signals are sent or received.)  The most commonly used modules
# are the standard X10 lamp module (StdLM) and standard X10 appliance
# module (StdAM).  Other modules currently supported by Heyu are listed 
# in x10config(5).  A standard X10 lamp module (StdLM) is the
# default (changeable with the DEFAULT_MODULE directive)
# for housecode|units which are not defined in an alias directive.
# A module_type should normally not be defined for mutiple-unit
# aliases, just for the single-unit aliases.  (The module characteristics
# are associated with the housecode|unit, however referenced.)
# 
# Some examples:

# ALIAS  front_porch        A1   StdLM
# ALIAS  back_porch         A2   StdLM
# ALIAS  porch_lights       A1,2

# ALIAS  tv_set             A3   StdAM
# ALIAS  living_room        A4   LM14A

# ALIAS  patio_landscape    A8   StdAM
# ALIAS  patio_lamppost     A9   StdLM
# ALIAS  all_patio_lights   A8,9

# Note: Prior versions of Heyu used a different format for 
# aliases - no ALIAS directive and the Housecode and Unitcode_string
# were separated by a space, e.g., simply:
#  front_porch  A  1
# Heyu will continue to accept this older format for compatibility,
# but its use is discouraged as modules cannot be specified.

# Scenes and Usersyns (User-defined synonyms):
# Format:  SCENE   Label Command1 <args> [; Command2 <args> [; ...
# Format:  USERSYN Label Command1 <args> [; Command2 <args> [; ...
# The label is limited to 32 characters and is case-sensitive.
# Scenes and Usersyns are both semicolon-separated lists of
# commands with their arguments which can be executed or used
# in macros as if their labels were ordinary Heyu commands.
# See 'man x10config' for the features and limitations of Scenes
# and Usersyns.  
# (In the current version of heyu, the ONLY distinction between
# scenes and usersyns is the 'show' menus in which they appear.)
# Some examples:

# SCENE  blinker  on A1; off A1; on A1; off A1
# USERSYN normal_lights  on front_porch; on back_porch
# SCENE   tv_on   on tv_set; dimb living_room 10

# Scene and usersyn definitions can include positional 
# parameters, e.g., $1, $2, which are replaced by actual
# parameters supplied when the scene/usersyn is run.

# USERSYN night_lights dimb front_porch $1; dimb back_porch $1
 
# Define the (writeable) directory where the Heyu state engine daemon 
# (started with 'heyu engine') is to write its log file 'heyu.log.<tty>'.
# The default is 'NONE', indicating no log file is to be written.

# LOG_DIR  NONE

# The entries in the log file are similar to those which appear in
# the heyu monitor, but in addition will include an entry when
# a script is launched, and unless redirected elsewhere, any
# text output from that script.

# Note that the log file will continue to grow.  Manually delete
# or trim it from time to time, or configure a Unix utility like
# 'logrotate' to manage this task automatically.

# If the Heyu state engine is running, Heyu can launch scripts
# (or any Unix commands) when it sees specified X10 signals.
# The format is:
#
#  SCRIPT [ -l label ] <launch conditions> :: [options] <command line>
#
# where label is an optional label, <launch conditions> tell
# Heyu under what conditions to launch the script, and 
# <command line> is the script command to be executed.
# The '::' (two colons) separator is mandatory since the launch
# conditions can be quite complex.
# See x10scripts(5) for details, but here's a simple example
# (with no label):
#
# ALIAS  doorbell  B1
# SCRIPT  doorbell on :: play $HOME/sounds/barking_dog.wav

# Users have the option of running either 'heyuhelper' in a manner
# similar to heyu 1.35 or general scripts as above with the 
# following directive.  The default is SCRIPTS, to run general scripts.

# SCRIPT_MODE  SCRIPTS       # SCRIPTS  HEYUHELPER

# (With the choice 'HEYUHELPER', a script named 'heyuhelper' on
# the user's path is run every time any X10 signal is received
# by heyu over the power line, assuming the heyu state engine
# daemon is running.)

###  The following directives apply when a schedule is ###
###  is uploaded to the CM11A interface.               ###

# The file name of the user's X10 schedule file in the Heyu base
# directory. The default is 'x10.sched'.  If you regularly use
# more than one, list them here and just comment/uncomment as
# appropriate, e.g.,

# SCHEDULE_FILE    x10.sched
# # SCHEDULE_FILE   normal.sched
# # SCHEDULE_FILE   vacation.sched

# The MODE directive - Heyu's two modes of operation:
# In the default COMPATIBLE mode, the schedule uploaded to the
# interface is configured to begin on Jan 1st of the current
# year and # is valid for 366 days - through Dec 31st of the
# current # year or Jan 1st of the following year, depending
# whether # the current year is a leap or common year.
# COMPATIBLE mode is the default.
#
# In HEYU mode the schedule uploaded to the interface is
# configured to begin on today's date and is valid for
# the number days of provided by the PROGRAM_DAYS directive.
# WARNING: The mere execution of X10's ActiveHome(tm) program
# under MS-Windows, or having its resident driver running, when 
# the interface has been programmed by Heyu in HEYU mode can 
# cause problems.  See 'man x10config' for details.

# MODE              COMPATIBLE      # COMPATIBLE  HEYU

# Number of days for which the interface is to be programmed
# when running in HEYU mode.  It is ignored in COMPATIBLE mode.
# (A shorter period can yield more accurate values for dawn 
# and dusk.)  The default is 366 days.

# PROGRAM_DAYS       366            # [number of days 1 to 366]

# Should Heyu combine events having the same date range, time, etc.,
# by concatenating the macros for similar events?   The default is YES.

# COMBINE_EVENTS    YES              # YES  NO

# Should Heyu compress uploaded macros by combining unit codes for the same
# housecode and command and eliminating duplicates?  E.g., 
#  (on A1; on B2; on A3, on B2) ==> (on A1,3; on B2)
# The default is NO

# COMPRESS_MACROS   NO               # YES  NO

# The user's Longitude and Latitude, needed for dawn/dusk calculations.
# There are no defaults.  Don't use these examples - put in values
# for your own location.

# LONGITUDE         W079:49      # [degrees:minutes East or West of Greenwich]
# LATITUDE          N36:04       # [degrees:minutes North or South of equator]

# For dawn/dusk related times, Heyu breaks up the schedule date intervals
# into subintervals, each with a constant value of dawn or dusk time.
# These directives instruct Heyu what value of dawn/dusk time to use.
# The default value is FIRST, i.e., that on the first day of the subinterval,
# which is most convenient for comparing Heyu's computations with actual.

# DAWN_OPTION       FIRST         # FIRST  EARLIEST  LATEST  AVERAGE  MEDIAN
# DUSK_OPTION       FIRST         # FIRST  EARLIEST  LATEST  AVERAGE  MEDIAN

# The following times allow bounds to be placed on the times of Dawn
# and Dusk computed by Heyu. For example, setting the value for
# MIN_DAWN to 06:30 will ensure that an event scheduled to be 
# executed at Dawn will occur at 06:30 during summer hours whenever
# the actual computed value of Dawn is earlier than that time.
# The value for these directives are specified as hh:mm Legal 
# (i.e., wall-clock) time, or the directives may be disabled with
# the word OFF, which is the default.
#
# Timer options DAWNLT, DAWNGT, DUSKLT, DUSKGT used in the Heyu
# schedule file will usually eliminate the need for these directives.
# See man page x10sched(5) for details.

# MIN_DAWN         OFF           # OFF or [hours:minutes 00:00-23:59]
# MAX_DAWN         OFF           # OFF or [hours:minutes 00:00-23:59]
# MIN_DUSK         OFF           # OFF or [hours:minutes 00:00-23:59]
# MAX_DUSK         OFF           # OFF or [hours:minutes 00:00-23:59]

# Directory to write reports and files other than the critical files
# The default is to write them in the Heyu base directory.

# REPORT_PATH  ./                  # [127 characters max.]

# Replace events having delayed macros with new events and new 
# undelayed macros when possible. (The purpose is to avoid pending
# delayed macros, which are purged when a new schedule is uploaded.)
# The default is YES.

# REPL_DELAYED_MACROS      YES     # YES  NO

# For test purposes, Heyu can write some additional files when
# the command 'heyu upload check' is executed.  This directive
# instructs Heyu to write these files.  The default is NO.

# WRITE_CHECK_FILES  NO           # YES  NO

Places

File x10.conf of Package heyu

Places