File change-udev-rules.diff of Package hplip

--- data/rules/56-hpmud.rules.change-udev-rules.orig	2013-10-11 11:38:53.000000000 +0200
+++ data/rules/56-hpmud.rules	2013-10-16 16:04:54.000000000 +0200
@@ -1,18 +1,43 @@
 # HPLIP udev rules file. Notify console user if plugin support is required for this device.
 
+# SUSE changed:
+#
+# Exchanged the rule to GOTO hpmud_usb_rules if SUBSYSTEM is "usb"
+# with the rule if SUBSYSTEM is "ppdev" to avoid that the "ppdev" rule
+# is needlessly processed when SUBSYSTEM is "usb".
+#
+# Added GOTO hpmud_rules_end rule to skip the hpmud_usb_rules
+# if SUBSYSTEM is not "usb" or if ENV{DEVTYPE} is not "usb_device" or if SUBSYSTEM is not "ppdev"
+# to avoid that the hpmud_usb_rules are needlessly processed.
+#
+# The rule to automatically "add the printer and install plugin" is disabled
+# because automated installation of non-free proprietary third-party software
+# (here the plugin from HP) should not happen and it can cause whatever kind
+# of strange behaviour see for example https://bugs.launchpad.net/bugs/1197416
+# and https://bugs.launchpad.net/bugs/1221348
+# while in contrast manual printer setup via hp-setup usually "just works"
+# and it is clear for the user what goes on and in case of failure what went wrong.
+#
+# Because the rule to automatically "add the printer and install plugin"
+# is also used to upload firmware into printers that need it
+# see https://bugs.launchpad.net/bugs/1220628
+# a rule that only uploads firmware into printers that need it is added.
+
 ACTION!="add", GOTO="hpmud_rules_end"
-SUBSYSTEM=="ppdev", OWNER="root", GROUP="lp", MODE="0664"
 SUBSYSTEM=="usb", ENV{DEVTYPE}=="usb_device", GOTO="hpmud_usb_rules"
-
+SUBSYSTEM=="ppdev", OWNER="root", GROUP="lp", MODE="0664"
+GOTO="hpmud_rules_end"
 
 LABEL="hpmud_usb_rules"
 
 # ENV{ID_HPLIP}="1" is for Ubuntu udev-acl
 ATTR{idVendor}=="03f0", ATTR{idProduct}=="????", OWNER="root", GROUP="lp", MODE="0664", ENV{sane_hpaio}="yes", ENV{libsane_matched}="yes", ENV{hp_test}="yes", ENV{ID_HPLIP}="1"
 
-
 # This rule will add the printer and install plugin
-ENV{hp_test}=="yes", PROGRAM="/bin/sh -c 'logger -p user.info loading HP Device $env{BUSNUM} $env{DEVNUM}'", RUN+="/bin/sh -c 'if [ -f /usr/bin/systemctl ]; then /usr/bin/systemctl --no-block start hplip-printer@$env{BUSNUM}:$env{DEVNUM}.service; else /usr/bin/nohup /usr/bin/hp-config_usb_printer $env{BUSNUM}:$env{DEVNUM} ; fi'"
+# ENV{hp_test}=="yes", PROGRAM="/bin/sh -c 'logger -p user.info loading HP Device $env{BUSNUM} $env{DEVNUM}'", RUN+="/bin/sh -c 'if [ -f /usr/bin/systemctl ]; then /usr/bin/systemctl --no-block start hplip-printer@$env{BUSNUM}:$env{DEVNUM}.service; else /usr/bin/nohup /usr/bin/hp-config_usb_printer $env{BUSNUM}:$env{DEVNUM} ; fi'"
+
+# This rule uploads firmware to HP USB printer devices if needed:
+ENV{hp_test}=="yes", PROGRAM="/bin/logger -p user.info udev hpmud.rules runs hp-firmware to test if HP device with USB vendor ID $attr{idVendor} and USB product ID $attr{idProduct} at USB bus ID $env{BUSNUM} and USB device ID $env{DEVNUM} needs firmware and if yes to upload it", RUN+="/usr/bin/hp-firmware -s $env{BUSNUM}:$env{DEVNUM}"
 
 # If sane-bankends is installed add hpaio backend support to dll.conf if needed.
 ENV{sane_hpaio}=="yes", RUN+="/bin/sh -c 'grep -q ^#hpaio /etc/sane.d/dll.conf;if [ $$? -eq 0 ];then sed -i -e s/^#hpaio/hpaio/ /etc/sane.d/dll.conf;else grep -q ^hpaio /etc/sane.d/dll.conf;if [ $$? -ne 0 ];then echo hpaio >>/etc/sane.d/dll.conf;fi;fi'"
@@ -20,5 +45,5 @@ ENV{sane_hpaio}=="yes", RUN+="/bin/sh -c
 # The following rule will disable USB autosuspend for the device
 ENV{libsane_matched}=="yes", RUN+="/bin/sh -c 'test -e /sys/$env{DEVPATH}/power/level && echo on > /sys/$env{DEVPATH}/power/level'"
 
-
 LABEL="hpmud_rules_end"
+