File sdparm.changes of Package sdparm
-------------------------------------------------------------------
Mon Sep 5 15:07:15 UTC 2022 - Ludwig Nussel <lnussel@suse.de>
- Use /usr/sbin (boo#1191094)
-------------------------------------------------------------------
Thu Jun 24 10:31:19 UTC 2021 - Ferdinand Thiessen <rpm@fthiessen.de>
- Update to version 1.12
* add Command duration limits T2A and T2B mpages
* add Sequestered command fields in Control extension mpage
* SAS/SPL disconnect-reconnect mpage: BILUNIT and CTLUNIT
fields added (21-021r3)
* vpd: SCSI Feature Sets [0x92]: add ZBC feature sets
* add SAT ATA Feature control mpage (20-085r4)
* block device char vpd page: add zoned strings
* expand Out of band management control mpage (spl5r08)
* vpd: add Format presets and Concurrent positioning
ranges pages
* vpd: standard inquiry: add hot_pluggable field
* sg_lib: allows access to cache mpage's WCE for nvme
- Update to version 1.11
* Allow ZBC mode pages to use existing SBC mpages
as permitted by zbc2r04 chapter 6.4.1 table 70
* add --out_mask=OM option for mode page control
bitmask (current, changeable, default and/or saveable)
* add --examine option to iterate over mode+vpd pages
* add Out of band management control mpage (spl5r01)
* expand SAS configure port mode page [0x19,0x2] with
configure port mode fields (spl5r07)
* accept additional transport acronyms (e.g. ib for srp)
* power condition mpage: rename fields IDLE->IDLE_A;
STANDBY->STANDBY_Z; ICT->IACT and SCT->SZCT
* device configuration extension mpage: expand PEWS
field with added PE_UN (PEWS units) field (ssc5r05)
* add Zoned block device control mpage (zbc2r04a)
* --defaults option can be used twice: reverts all
pages to their defaults (new in spc5r11, RTD bit)
* vpd: decode TransportIDs in SCSI port page
* command=capacity with --long force read capacity(16)
with full reporting of response
* --wscan option: expand bus type to include NVMe
* mode page output with -HHH suitable for --inhex=
* add flexible geometery page (obsolete) sbc2r00
* point svn:externals to rev 843 of sg3_utils [v 1.45]
* update BSD license from 3 to 2 clause aka FreeBSD
license (without reference to FreeBSD project)
-------------------------------------------------------------------
Wed Aug 24 17:49:33 UTC 2016 - alexander_naumov@opensuse.org
- Update to version 1.10
* add --inhex=FN option for decoding without device present,
FN is interpreted as response to mode sense(10) command
* add --raw option to interpret FN as binary (def: ASCII hex)
* add --pdt=PDT option for use with --inhex=FN
* --quiet used twice hides changeable, default + saved
* add IO advice hints grouping mode page (sbc4r06, 8)
* add Unit serial number VPD page specific sanity check
* add NO_PI_CHK to Supported block lengths and protection
types VPD page
* add Background operation control mpage (sbc4r07)
* Read-write error recovery mpage: add Misaligned writes
reporting field (MWR)
* sync tape mpages with ssc5r02
* add Block limits extension VPD page
* add Device constituents VPD page
* add LB protection VPD page (ssc5r02a)
* LB provisioning VPD page: expand LBPRZ, add Minimum and
Threshold percentage fields
* device identification VPD page: add decoding for locally
assigned UUIDs (spc5r08)
* the --inhex=FN option together with --inquiry decodes
FN as a single VPD page
* improve lto5 and lto6 vendor mpage support
* sync to spc5r08 and sbc4r10
* add SAS G5 (22.5 Gbps) settings (spl4r06)
* point svn:externals to rev 663 of sg3_utils
* upgrade automake to version 1.15 (U15.10)
* autogen.sh: upgrade to buildconf 20091223 version
-------------------------------------------------------------------
Sun Dec 28 15:04:12 UTC 2014 - p.drouand@gmail.com
- Update to version 1.09
+ decode Third Party Copy VPD page
+ Supported block lengths and protection types (sbc4r01) +
Block device characteristics extension VPD pages added
+ zoned block device characterics VPD page added (zbc-r01c)
+ fix manufacturer-assigned serial number VPD page length
+ device id VPD: T10 vendor identification designator clean up
+ block device characteristics VPD: add ZONED (sbc4r04)
+ SAS/SPL disconnect-reconnect mpage: expand
+ SAS protocol specific port mpage: add MAXR field (spl4r01)
+ standard inquiry response (sinq): add LU_CONG
+ change ibm vendor code to lto5 and lto6
+ point svn:externals to rev 620 of sg3_utils
+ upgrade automake to version 1.14.1
+ configure: add --disable-libsgutils so build bypasses that
library if present
+ win32: some --wscan and compile fixes
-------------------------------------------------------------------
Wed Oct 23 15:33:48 UTC 2013 - p.drouand@gmail.com
- Remove %fillup_prereq and %insserv_prereq; package doesn't provide
any sysvinit script
-------------------------------------------------------------------
Thu Jun 13 13:56:56 UTC 2013 - jengelh@inai.de
- Update to new upstream release 1.08
* New utilities: scsi_ch_swp, sas_disk_blink
* Tracked changes at t10.org since January 2012:
* device id VPD: add protocol specific port identifier
* control extension mpage: add max sense data length
* power condition mpage: FIDCPC->CCF_IDLE, FSBCPC->CCF_STAND,
FSTCPC->CCF_STOPP (spc4r34+)
* caching mpage: add SYNC_PROG field (sbc3r33)
* block device characteristics VPD page additions sbc3r34
* extended inquiry vpd page: add max supported sense data length
* protocol-specific port information VPD page for SAS SSP,
persistent connection (spl3r2), power disable (spl3r3)
* allow --readonly with --set= and --clear=
* add placeholder for third party copy VPD page
* supply more information if a UA occurs
- Normalized install procedure
- Build with libsgutils support
-------------------------------------------------------------------
Sun Apr 22 11:46:53 UTC 2012 - puzel@suse.com
- Update to version 1.07
- LB provisioning + Block limits VPD pages to sbc3r27
- Enhanced phy control page: optical mode enabled (spl-r07)
- Phy control and discover page: sync to spl2r02
- sync with spc4r31+32 (handle status good with sense)
- extented inquiry VPD: add POA_SUP, HRA_SUP and VSA_SUP
- application tag mode page subcode 0xf0->0x2 (sbc3r28)
- add 'sinq' pseudo VPD page for standard inquiry response
- add power consumption mode and VPD pages (spc4r33)
- point out some mode page numbers are vendor specific
-------------------------------------------------------------------
Tue May 24 17:31:45 CEST 2011 - dimstar@opensuse.org
- Update to version 1.06:
+ allow upper and lower case in field, (mode and vpd) page,
vendor, transport or command matching
+ control mode page: add ATMPE and RWWP fields (spc4r27)
+ extended inquiry vpd page: add extended self test completion
minutes field (spc4r27)
+ power control mode page: PM_BG_PRECEDENCE field (spc4r24)
- FIDCPC, FSBCPC, FSTCPC fields (spc4r25)
+ sbc3r25 renames 'thin' provisioning' to 'logical block
provisioning'; changes mode+vpd page and field names
- add Application tag mode page
- add SITPUA bit to logical block provisioning mode page
+ fix '-eal' problem with vendor pages
+ point svn:externals to rev 334 of sg3_utils
-------------------------------------------------------------------
Fri Aug 13 11:56:39 CEST 2010 - dimstar@opensuse.org
- Update to version 1.05:
+ add '--readonly' option especially for '-C start' and
'-C stop' on ATA disks.
+ Control mode page updates (spc4r23)
+ add Control data protection mode page (ssc4r01)
+ block device characteristics VPD page: decode form factor
+ extended inquiry VPD page: activate_microcode+r_sup (spc4r23)
+ Automation device serial number and Data transfer device
element address VPD pages (ssc4r01)
+ add SBC Referrals VPD page (sbc3r22)
+ expand SBC Thin provisioning VPD page (sbc3r22)
+ expand SBC Block limits VPD page (sbc3r22)
+ SAS-2.1 specification split, upper layers placed in SPL
- add enable_slumber and enable_partial fields to
Enhanced phy control mode page
+ add AM_MAINTAINER_MODE to configure.ac to lessen build issues
+ build infrastructure change to use libsgutils2 if available
- Changes from version 1.04:
+ add SAT ATA Power condition mode page (sat2r06)
+ add SBC Thin provisioning mode page (sbc3r20)
+ add SBC Thin provisioning VPD page (sbc3r20)
+ sync with spc4r21
+ add Power condition, update extended inquiry VPD pages
+ smc3: add Device capabilities + Extended device
capabilities + Transport geometry parameters mode pages
+ prepare for Thin provisioning VPD and mode pages
+ expand block limits VPD page
+ update Power condition mode page
+ rename SAS-2 phy mode page to Enhanced phy control (SAS)
+ add ADC mode (sub)page place holders
+ print mode page descriptors in full in more contexts
+ add linux bsg support
+ scripts/sas_disk_blink: moved here from sg3_utils package
+ rework the '-w' option (win32) per sg_scan in sg3_utils
+ change SDPARM_* constants to SG_LIB_*
+ remove sdparm.html, refer to its url in sdparm.8
+ sdparm.spec: correction to configure call
-------------------------------------------------------------------
Tue Aug 12 18:40:54 CEST 2008 - garloff@suse.de
- Update to sdparm-1.03:
* supports more than one device on command linx
* speed[=val] and profile commands for MMC
* Extended Inquiry VPD page updated (spc4r15)
* SAS protocol-specific port mpage (add CAWT, RTOL)
* minor cleanups
-------------------------------------------------------------------
Fri May 23 10:11:29 CEST 2008 - hare@suse.de
- Using 'Provides' keyword to clean update dependency.
-------------------------------------------------------------------
Thu Apr 24 14:51:23 CEST 2008 - hare@suse.de
- Split off from the original scsi package.
