File cntlm.init of Package cntlm
#!/bin/sh
#
# Copyright (c) 2009 Scorpio IT, Deidesheim, Germany
#
# Author: Christian Wittmer
# Please send feedback to rpm (at) scorpio-it (dot) net
#
# /etc/init.d/cntlm
# and its symbolic link
# /(usr/)sbin/rccntlm
#
### BEGIN INIT INFO
# Provides: cntlm
# Required-Start: $syslog $network $time
# Should-Start: $remote_fs
# Required-Stop: $syslog $network $time
# Should-Stop: $remote_fs
# Default-Start: 2 3 5
# Default-Stop: 0 1 6
# Short-Description: start/stop the cntlm proxy
# Description: ntlm is meant to be given your proxy address and becomming
# the primary proxy then, listening on a selected local port.
# You point all your proxy-aware programs to it and don't ever
# have to deal with proxy authentication again.
### END INIT INFO
#
# Note on runlevels:
# 0 - halt/poweroff 6 - reboot
# 1 - single user 2 - multiuser without network exported
# 3 - multiuser w/ network (text mode) 5 - multiuser w/ network and X11 (xdm)
#
# Check for missing binaries (stale symlinks should not happen)
# Note: Special treatment of stop for LSB conformance
cntlm_bin="/usr/sbin/cntlm"
test -x $cntlm_bin || { echo "$cntlm_bin not installed";
if [ "$1" = "stop" ]; then exit 0;
else exit 5; fi; }
# Check for existence of needed sysconfig file and read it
cntlm_config="/etc/cntlm.conf"
test -r $cntlm_config || { echo "$cntlm_config not existing";
if [ "$1" = "stop" ]; then exit 0;
else exit 6; fi; }
# Check for existence of needed sysconfig file and read it
cntlm_sysconfig="/etc/sysconfig/cntlm"
test -r $cntlm_sysconfig || { echo "$cntlm_sysconfig not existing";
if [ "$1" = "stop" ]; then exit 0;
else exit 6; fi; }
# Read config
. $cntlm_sysconfig
# some defaults
cntlm_desc="CNTLM Authentication Proxy"
cntlm_pid="/var/run/cntlm/cntlmd.pid"
cntlm_user="-U ${CNTLM_USER:=cntlm}"
cntlm_opts=${CNTLM_OPTS:=""}
# if no "Proxy" is set in cntlm.conf try '127.0.0.1:3128' as a default
if [ `/bin/cat $cntlm_config | grep -e "^Listen" >/dev/null; echo $?` -eq 0 ]; then
cntlm_listen=
else
cntlm_listen="-l ${CNTLM_LISTEN:=127.0.0.1:3128}"
fi
# check for pid_dir
[ ! -d /var/run/cntlm ] && {
install -d -m0755 -o ${CNTLM_USER:=cntlm} -g root /var/run/cntlm;
}
# Source LSB init functions
# providing start_daemon, killproc, pidofproc,
# log_success_msg, log_failure_msg and log_warning_msg.
# This is currently not used by UnitedLinux based distributions and
# not needed for init scripts for UnitedLinux only. If it is used,
# the functions from rc.status should not be sourced or used.
#. /lib/lsb/init-functions
# Shell functions sourced from /etc/rc.status:
# rc_check check and set local and overall rc status
# rc_status check and set local and overall rc status
# rc_status -v be verbose in local rc status and clear it afterwards
# rc_status -v -r ditto and clear both the local and overall rc status
# rc_status -s display "skipped" and exit with status 3
# rc_status -u display "unused" and exit with status 3
# rc_failed set local and overall rc status to failed
# rc_failed <num> set local and overall rc status to <num>
# rc_reset clear both the local and overall rc status
# rc_exit exit appropriate to overall rc status
# rc_active checks whether a service is activated by symlinks
. /etc/rc.status
# Reset status of this service
rc_reset
# Return values acc. to LSB for all commands but status:
# 0 - success
# 1 - generic or unspecified error
# 2 - invalid or excess argument(s)
# 3 - unimplemented feature (e.g. "reload")
# 4 - user had insufficient privileges
# 5 - program is not installed
# 6 - program is not configured
# 7 - program is not running
# 8--199 - reserved (8--99 LSB, 100--149 distrib, 150--199 appl)
#
# Note that starting an already running service, stopping
# or restarting a not-running service as well as the restart
# with force-reload (in case signaling is not supported) are
# considered a success.
case "$1" in
start)
echo -n "Starting ${cntlm_desc}: "
## Start daemon with startproc(8). If this fails
## the return value is set appropriately by startproc.
/sbin/startproc -p $cntlm_pid $cntlm_bin -P $cntlm_pid $cntlm_listen $cntlm_user $cntlm_opts &>/dev/null
# Remember status and be verbose
rc_status -v
;;
stop)
echo -n "Shutting down ${cntlm_desc}: "
## Stop daemon with killproc(8) and if this fails
## killproc sets the return value according to LSB.
/sbin/killproc -p $cntlm_pid -TERM $cntlm_bin &>/dev/null
# Remember status and be verbose
rc_status -v
;;
try-restart|condrestart)
## Do a restart only if the service was active before.
## Note: try-restart is now part of LSB (as of 1.9).
## RH has a similar command named condrestart.
if test "$1" = "condrestart"; then
echo "${attn} Use try-restart ${done}(LSB)${attn} rather than condrestart ${warn}(RH)${norm}"
fi
$0 status
if test $? = 0; then
$0 restart
else
rc_reset # Not running is not a failure.
fi
# Remember status and be quiet
rc_status
;;
restart)
## Stop the service and regardless of whether it was
## running or not, start it again.
$0 stop
$0 start
# Remember status and be quiet
rc_status
;;
force-reload|reload)
## Signal the daemon to reload its config. Most daemons
## do this on signal 1 (SIGHUP).
## If it does not support it, restart the service if it
## is running.
# cntlm does not support SIGHUP, so restart
echo -n "Reload ${cntlm_desc}: "
## if it supports it:
#/sbin/killproc -p $cntlm_pid -HUP $cntlm_bin
# Remember status and be verbose
#rc_status -v
## Otherwise:
$0 try-restart
# Remember status and be quiet
rc_status
;;
status)
echo -n "Checking for ${cntlm_desc}: "
## Check status with checkproc(8), if process is running
## checkproc will return with exit status 0.
# Return value is slightly different for the status command:
# 0 - service up and running
# 1 - service dead, but /var/run/ pid file exists
# 2 - service dead, but /var/lock/ lock file exists
# 3 - service not running (unused)
# 4 - service status unknown :-(
# 5--199 reserved (5--99 LSB, 100--149 distro, 150--199 appl.)
# NOTE: checkproc returns LSB compliant status values.
/sbin/checkproc -p $cntlm_pid $cntlm_bin
# NOTE: rc_status knows that we called this init script with
# "status" option and adapts its messages accordingly.
# Remember status and be verbose
rc_status -v
;;
*)
echo "Usage: $0 {start|stop|status|try-restart|restart|force-reload|reload}"
exit 1
;;
esac
rc_exit
