- Add cma-default option to vc4-kms-v3d overlay to mimic the previous default
  behaviour, which used the kernel's default size. For now we still set the CMA
  trough the kernel command line, that will change in the future. (bsc#1167761)

- Get rid of rpi4-thermal overlay, not needed anymore
- Get rid of rpi4-firmware-dma-ranges overlay, not needed anymore
- Get rid of rpi4-gpio-names overlay, not needed anymore

• Files Changed
• Browse Source

Implement jsc#SLE-9545.

• Files Changed
• Browse Source

- Add rpi4-firmware-dma-ranges overaly which fixes touch input on the official
  7" display (bsc#1167147)

- Add rpi4-firmware-dma-ranges overaly which fixes touch input on the official
  7" display (bsc#1167147)

• Files Changed
• Browse Source

- Add uboot-bcm2835-pl011 overlay, which fixes the serial port compatible name
  as expected by u-boot, relevant for RPi, RPi2 and RPi0 families (bsc#1166414)

• Files Changed
• Browse Source

- Add rpi4-gpio-names overlay so as to have a consistent way to access GPIOs (bsc#1164722)

- Remove rpi4-pcie-ib-size-fix as raspberrypi-firwamre-dt removed it (bsc#1165143)

• Files Changed
• Browse Source

- Update to f4b5869 (2020-02-12) (bsc#1163476):
  * firmware: board_info: Fix GPIO expander reset trait
  * firmware: gencmd: Fix measure_clock name for CLOCK_OUTPUT_108
  * firmware: platform: Compromise on gpu overclock settings
- After the rpi-5.5.y update in raspberrypi-firmware-dt:
  * Remove rpi4-genet as it's not needed anymore
  * Remove gpu_mem entry for rpi4

- Update to be2713bed4 (2020-01-16):
  * firmware: master: arm_ldconfig: Support multiple initramfs files
    See: #1318
  * firmware: power: Make pmicrd/pmicwr available to all
  * firmware: arm_ldconfig: Support multiple initramfs files
    See: #1318
  * firmware: Add support for backlight enable
  * firmware: Revert mmal: Support 64 bit clients
    See: raspberrypi/userland#586
  * firmware: arm_dt/dtoverlay fixes for ARM side camera driver power control
  * firmware: Fixup for vcgencmd display_power
    See: #1224
  * firmware: Add hdmi_wifi_pixel_freq_adj config option

- Update to 0c01dbefba (2019-12-11):
  * firmware: platform: Allow fixed voltage with avs_disable=1
  * firmware: EMMC: Use PLLD for EMMC for 250MHz host-clock
    See: #1289
  * firmware: platform: Round down effective frequencies when they exceed max
    See: #1290
  * firmware: arm_loader: Pass video mode via kernel command for composite
    See: #1285

• Files Changed
• Browse Source

- Add rpi4-thermal device tree overlay for RPi4 (bsc#1160311)

- Add rpi4-thermal device tree overlay for RPi4 (bsc#1160311)

• Files Changed
• Browse Source

- Disable overscan by default (bsc#1160473)
- Disable overscan by default (bsc#1160473)

• Files Changed
• Browse Source

- Add custom gpu_mem config for RPi4 (bsc#1158406)

• Files Changed
• Browse Source

- Load rpi4-genet-overlay to fix the compatible for the network device (jsc#SLE-7771)

- Enable rpi4-cma dt overlay to properly setup CMA on that platform (SLE-7771)
- Enable rpi4-pcie-ib-size-fix dt overlay to properly setup PCIe on that
  platform (SLE-7771)

- Update to 6e4a7232c (2019-11-19):
  * firmware: platform: Differentiate between boostable and turbo clocks
  * firmware: arm_dt: Set WL_ON and BT_ON from .dtb
  * firmware: Fixup chosing of bit depth in legacy graphics
    See: raspberrypi/linux#3331
  * firmware: vec: Setup WideScreen Signalling outside of copy protection
    See: https://www.raspberrypi.org/forums/viewtopic.php?f=28&t=256489
  * firmware: Add global reset mailbox
  * firmware: 2711: De-couple start.elf clock setup from the bootloader
  * firmware: scaler: Correct defines for SCALER_POS0_START_Y_[MASK|SHIFT] (HVS4)
  * firmware: platform: Fix missing HDMI PHY power down bit
  * firmware: Reduce voltage as part of DVFS
  * firmware: arm-loader: Inherit 2711 mac-address from the bootloader
    See: http://git/vc4/vc4/merge_requests/687
  * firmware: arm_loader: Respect all required frequencies when throttling
  * firmware: Fixup vcgencmd display_power return values

- If booting RPi in arm64 mode or not will be set by u-boot through
  ubootconfig.txt. This allows to build u-boot for RPi3/4 with 32-bit.

- config changes for RPi3:
  * delete upstream-aux-interrupt as not present anymore
  * set arm_control for RPi3 only
  * add RPi3 overlays

• Files Changed
• Browse Source

- add RPi4 config options

- Update to a16470ad4 (2019-09-30)
  * firmware: platform: Set up emmc clock earlier
  * firmware: hdmi: Implement platform_display_power on 2711
    See: #1224
  * firmware: arm_loader: Pass overscan settings to the kernel
  * firmware: arm_loader: Add option disable_fw_kms_setup to stop FKMS setup by FW
  * firmware: hdmi: Use pixel clock multiplier to determine the core clock
  * firmware: Fixups for composite output mode
    See: #1223
  * firmware: platform: Allow display_power to be queried from gencmd
    See: #1224
  * firmware: arm_loader: Fix no-DT and upstream handling
    See: #1250
  * firmware: Round up HDMI0 minimum core clock
  * firmware: board_info: Support bcm2710- and bcm2837- Pi 2 DTBs
    See: raspberrypi/linux#3234
  * firmware: power: bcm2711: Rescale the GPIO pad power
  * firmware: brfs: Add GENET driver for 2711
  * firmware: bootloader_state: Add network state and bootmode configuration
  * firmware: bootloader_state: Fix mask for EEPROM header magic
  * firmware: arm_loader: Fix initial_turbo getting stuck
    See: #1005
  * firmware: ldconfig: Support [edid=*] to mean any HDMI monitor
    See: #1136
  * firmware: image_fx: Remove restriction that output stride must match input stride
  * firmware: image_fx: Remove spamming log line
  * firmware: platform: Switch to divide by one when arm_freq exceeds 2GHz
  * firmware: Add EMMC support to 2711 Arasan EMMC driver

• Files Changed
• Browse Source

initialize package

• Browse Source